

Lancaster Trailer Supplies
A typical Trailer Supplies job in Lancaster starts the same way: you tell us what you're hauling and what trailer you have, we narrow the part family (running gear, brakes, lights, coupler, jack, electrical), then we confirm the measurements and ratings that actually decide fit. If you're replacing a worn component, we'll compare what's on the trailer now to the correct spec, pull the right parts from stock, and make sure you leave with everything needed to finish the work without extra trips, including the small hardware and wiring pieces that are easy to miss.
Arrow Trailer Supplies keeps an extensive inventory for trailer needs, and our technicians are professionally trained and trained to service all makes and models. That matters when the part in your hand "looks right" but has a different bolt pattern, bearing set, or brake flange offset. Getting the correct match up front prevents uneven tire wear, hot hubs, weak braking, and lights that fail at the worst time on a long Lancaster drive.
Choosing the right Trailer Supplies for a correct fit
Trailer parts aren't universal. Two trailers with the same deck size can have different axle capacities, brake types, and hub faces. The quickest way to get the right supplies is to bring details that remove guesswork.
- Trailer info: VIN plate details if available, GVWR, axle rating, and wheel size.
- Running gear measurements: hub face to hub face, spring center to spring center, and the axle tube diameter if you can measure it.
- Brake details: drum vs. disc, electric vs. hydraulic, and the brake size (common sizes exist, but we confirm rather than assume).
- Old parts: a hub, bearing, seal, coupler, jack, light, or connector you're replacing. Even a clear photo with a tape measure helps when the trailer can't come in.
We'll also ask how you use the trailer in Lancaster. A utility trailer making short runs doesn't stress components the same way as a car hauler or equipment trailer that sees longer highway pulls and heavier tongue weight. That usage drives smart choices in brakes, breakaway components, couplers, and jack capacity.
Running gear: axles, hubs, bearings, brakes, and what goes wrong
Running gear is the core of most Trailer Supplies requests because it's where wear shows up first. Heat, dust, and stop-and-go towing accelerate bearing and brake wear, and Lancaster conditions can push components hard if maintenance gets skipped. The goal is simple: smooth rolling hubs, controlled braking, and a suspension setup that tracks straight without chewing through tires.
Common running-gear items we help match include:
- Hubs and drums: correct bolt pattern, stud size, and bearing races that match your spindle.
- Bearings and seals: the right inner/outer bearing set and seal dimensions. A "close enough" seal is a grease leak waiting to happen.
- Electric brake parts: complete backing plates, magnet kits, shoes, springs, and adjusters matched to size and mounting flange.
- Axle and suspension components: springs, hangers, equalizers, shackles, and U-bolts matched to axle diameter and suspension style. See our Trailer Axles inventory for common sizes and specs.
If you've ever replaced "just the bearing" and still had a hot hub, the usual culprit is a mismatch in the bearing/race pair, a worn spindle, an incorrect seal that let grease out and dust in, or a brake dragging because of adjustment issues. Our trained technicians can help diagnose those tough cases so you buy the parts that fix the root problem, not just the symptom you noticed first.
Warning signs that should change what you buy, not just how soon you buy it:
- Grease on the inside of the wheel: usually points to a seal problem, not only a bearing problem.
- One hub hotter than the others: can indicate a brake issue, a bearing preload problem, or damaged races.
- Pulsing or weak trailer brakes: can be electrical, adjustment, worn friction material, or drum condition.
- Uneven tire wear: can come from bent components, worn suspension hardware, or incorrect axle alignment.
Couplers, jacks, safety hardware, and the parts people overlook
Beyond axles and brakes, most breakdowns start with small, ignored components. A coupler that doesn't latch smoothly or a jack that binds under load turns a quick hookup into a risky one. In Lancaster, where trailers see frequent loading and unloading for work and recreation, these parts get cycled constantly.
We stock and help you select the right hookup and support pieces, including:
- Couplers and trailer tongue parts: matched to the correct ball size, mounting style, and trailer weight rating.
- Jacks: side-mount, top-wind, A-frame, and other common configurations sized for tongue weight and mount clearance.
- Safety chains, hooks, and hardware: chosen to match the trailer's duty level and mounting points.
- Breakaway components: switches, batteries, and related wiring items for braked trailers.
The right choice often comes down to clearance and geometry, not only capacity. For example, a jack that's rated high enough still fails your day-to-day use if it won't clear the ground on a driveway approach, or if the handle swing hits the propane tray or toolbox. We'll ask where it mounts, how much space you have, and how you use the trailer, then match the supplies to those constraints.
Electrical and lighting supplies that survive real towing in Lancaster
Trailer lighting problems are rarely "just a bad light." They're usually a weak ground, corroded connectors, damaged wire, or a mismatch between the vehicle plug and trailer wiring. Getting reliable lights means choosing the correct connector, protecting the wiring, and making clean connections that stay intact over miles of vibration.
Typical electrical Trailer Supplies requests include wiring connectors, junction boxes, lights, lenses, and the pieces needed to rework a harness cleanly. If you're upgrading or repairing, plan on addressing:
- Connector type: confirm what your tow vehicle uses and what your trailer is wired for before buying adapters or new plugs.
- Grounding: many "intermittent" lights are a ground issue, especially on painted or rusty frames.
- Wire protection: routing, loom, and strain relief matter because rubbing on the frame will eventually cut insulation.
If you're not sure what failed, our technicians can help you pinpoint whether you need a single replacement light, a connector repair, or a cleaner rewire approach. That way you don't leave with a bag of parts that still won't fix the flicker you're chasing.
How we help you get the right parts fast
Trailer parts selection gets complicated because manufacturers change designs over time, and previous owners sometimes modify trailers. Arrow Trailer Supplies stocks trailer running gear from many manufacturers for repairs or new trailer fabrications, and we pair that inventory with product knowledge so you're not guessing at the counter.
Here's how we keep the process practical:
- Identify the system: running gear, brakes, coupler/jack, or electrical.
- Confirm the deciding specs: measurements, bolt patterns, bearing numbers, brake size, connector type, or mount style.
- Build the complete parts list: not only the main component, but seals, hardware, wiring, or mounting pieces that make the repair complete.
- Sanity-check the outcome: talk through how the trailer is used in Lancaster and make sure the parts match the load and conditions.
Founded in 1965, we've seen the common ways trailer parts get mismatched, especially on hubs, bearings, brakes, and couplers. That experience shows up in the questions we ask before you buy, and in the small add-ons we recommend only when they're part of doing the job correctly.
FAQ: buying Trailer Supplies in Lancaster
Do I need to bring my trailer in to match parts?
No. Bringing the old part, the bearing numbers, and a few key measurements is often enough. If the trailer has been modified or parts are missing, bringing the trailer in makes identification faster and prevents a mismatch.
How do I identify the correct bearings and seal?
The most reliable method is bearing numbers stamped on the bearing itself, plus measuring the seal size if it isn't marked. Matching only by trailer size or "it looks the same" is where wrong parts happen.
Should I replace the whole brake assembly or only the shoes and magnets?
If the backing plate hardware is worn, corroded, or the adjuster is seized, a complete assembly is usually the cleaner repair because it restores the full mechanism at once. If the hardware is in good shape, targeted parts can make sense. The condition of the drum and wiring also matters.
My trailer lights work sometimes. What supplies usually fix that?
Intermittent lights usually come down to grounding, connectors, or damaged wire. The right supplies often include a new plug, a junction point, clean ground hardware, and protected wiring, not only a replacement lamp.
What information helps you match a coupler or jack correctly?
Bring the coupler style, mounting method, ball size, and the trailer's weight rating. For jacks, we'll also want the mount type and clearance needs so the jack fits your tongue setup and actually cranks without interference.
If you're buying Trailer Supplies in Lancaster because something failed mid-use, don't just replace the obvious broken piece. Bring what you can, share what you felt (noise, heat, pull, flicker), and we'll help you match parts that correct the cause, not only the aftermath.
To get started, gather the trailer details and the part you're replacing, then reach out to Arrow Trailer Supplies. You'll get straightforward guidance from people who work with trailer running gear and towing hardware every day, backed by an extensive inventory and trained technicians when the problem isn't simple.
